思科认证考试
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）A、Router(config)#router ospf 1B、Router(config)#router ospf 0C、Router(config)#router ospf area 0D、Router(config-router)#network 192.1
题目
Which commands are required to properly configure a router to run OSPF and to add network 192.168.16.0/24 to OSPF area 0?（）
- A、Router(config)#router ospf 1
- B、Router(config)#router ospf 0
- C、Router(config)#router ospf area 0
- D、Router(config-router)#network 192.168.16.0 0.0.0.255 area 0
- E、Router(config-router)#network 192.168.16.0 0.0.0.255 0
- F、Router(config-router)#network 192.168.16.0 255.255.255.0 area 0
参考答案和解析
相似问题和答案
第1题：
how many neighbor commands required for establish ibgp peers in 4 routers？
正确答案: If using IBGP full-mesh to establish IBGP peer and no update-source is specified， 12 neighbor command is need.
If RR is used，it could be 8 command using for ibgp establishing when there are 1 RR，2 client and 1 nonclient and no update-source is specified.
第2题：
A system administrator has edited the necessary files for setup of an AIX system to serve as a bootp server. Which of the following commands is required to complete the activation？（）
- A、telinit -q
- B、startsrc -s bootpd
- C、refresh -s inetd
正确答案:C
第3题：
You have just issued the command commit confirmed and your network continues to be operational with no further changes required. You issue a commit and-quit. A short time later, users start complaining about network problems. Which commands (in order) need to be entered to resolve this issue?（）
A.A
B.B
C.C
D.D
第4题：
Which of the following commands should an AIX system administrator invoke to check if the required device-dependent software is missing？（）
- A、dbx
- B、cfgmgr
- C、telinit q
- D、lsdev -Cc adapter
正确答案:B
第5题：
Which two commands are required to enable multicast on a router， knowing that the receivers only support IGMPv2？（）
- A、ip pim rp-address
- B、ip pim ssm
- C、ip pim sparse-mode
- D、ip pim passive
正确答案:A,C
第6题：
For the p5 590 and p5 595 servers, the HMC must be directly attached. Why is the use of a private service network between HMC and the p5 590 required?（）
- A、The Bulk Power Controllers are dependent upon the HMC to provide them with DHCP addresses.
- B、A firewall is required to isolate the private network from any of the open networks to which the HMC is attached.
- C、Network communications can be implemented through an open network. No private network is required but it is recommended.
- D、All p5 590 and 595 servers are shipped with one service processor card. A private network is required to manage DHCP addresses.
正确答案:A
第7题：
Which of the following commands provides data plane information required to forward a packet toa specific ip address？（）
- A、sh ip route
- B、sh ip cef 〈ip_address〉
- C、sh adjacency 〈ip_address〉
- D、sh ip route 〈ip_addres$〉
- E、sh ip adjacency 〈/p_address〉
- F、sh ip cef 〈mac_addrQss〉〈ip_address〉
正确答案:B
第8题：
An engineer is reviewing another engineer‘s sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?（）
A. tunnel source
B. tunnel destination
C. tunnel mode
D. All these commands are requireD
第9题：
The company auditors require a System p administrator to archive detailed information from each of their systems. Which of the following commands will accomplish this task（）
- A、snap -a
- B、snap -i
- C、prtconf
- D、lsconf
正确答案:A
第10题：
A System p administrator has been instructed to verify that all filesets have all required requisitesand are completely installed. Which of the following commands will provide this information（）
- A、lslpp
- B、lppchk
- C、geninstall
- D、installp
正确答案:B