IBM认证考试

Which command enables new devices that are connected to the scsi5 adapter without performing a full scan of the system?（）A、cfgmgr -f scsi5B、cfgmgr -i scsi5C、cfgmgr -t scsi5D、cfgmgr -l scsi5

题目

Which command enables new devices that are connected to the scsi5 adapter without performing a full scan of the system?（）

  • A、cfgmgr -f scsi5
  • B、cfgmgr -i scsi5
  • C、cfgmgr -t scsi5
  • D、cfgmgr -l scsi5
如果没有搜索结果，请直接 联系老师 获取答案。
如果没有搜索结果，请直接 联系老师 获取答案。
相似问题和答案

第1题：

An administrator tries to change the checksum_offload setting on ent0, but the chdev command responds that the adapter is busy.What can be done to resolve this?()

A.Use chdev with -P flag and run cfgmgr.

B.Use chdev with -R flag and run cfgmgr.

C.Use chdev with -P flag and reboot the system.

D.Use chdev with -R flag and reboot the system.


参考答案：C

第2题：

A system administrator notices that one of the mirrored disks, hdisk7 on datavg, has had a hardware failure. What is the best method of recover without causing additional problems?()

A.unmirrorvg datavg hdisk7 reducevg datavg hdisk7 replace the physical volume, run cfgmgr extendvg datavg hdisk7 mirrovg datavg hdisk7

B.varyoffvg datavg Rmdev -l hdisk7 -d Replace the physical volu,e run cfgmgr The system will automatically remirror when the disk is replaced

C.unmirrorvg datavg hdisk7 rmdev -l hdisk7 - d replace the physical volume, run cfgmgr extendvg datavg hdisk7 The system will automatically remirror when the disk is replaced.

D.unmirrorvg datavg hdisk7 reducevg data hdisk7 rmdev -l hdisk7 -d replace the physical volume, run cfgmgr extendvg datavg hdisk7 mirrovg datavg


参考答案：D

第3题：

While configuring a new adapter using cfgmgr, an administrator receives a warning message indicating that some device packages are not installed. Additionally, the adapter displays in the Defined state.Which command will resolve the issue and make the adapter available?（）

A.shutdown -Fr

B.cfgmgr -i <lpp_source>

C.mkdev -l <device_name>

D.mknode /dev/<device_name>


参考答案：B

第4题：

A customer has a failing HBA adapter and needs to identify the location of the adapter.  Which of the following AIX commands should the specialist recommend the customer review？（）

  • A、rmdev
  • B、chdev
  • C、drslot
  • D、cfgmgr

正确答案:C

第5题：

A system’s backups are failing. Error log analysis indicates that there is either a hardware or media problem. Which command is used to determine if there is a hardware problem with the tape drive？（）

  • A、diag
  • B、lscfg
  • C、lsdev
  • D、cfgmgr

正确答案:A

第6题：

Which command enables new devices that are connected to the scsi5 adapter without performing a full scan of the system?()

A.cfgmgr -f scsi5

B.cfgmgr -i scsi5

C.cfgmgr -t scsi5

D.cfgmgr -l scsi5


参考答案：D

第7题：

A graphics card has been added and the system rebooted. When running the lsdev－Cc adapter, the graphics card is not listed in the output. Which of the following actions should be performed?()

A.Reboot system sing the mkdev -l command.

B.Install device support suing the cfgmgr -i command.

C.Use the SMIT console to redirect the console.

D.Use SMIT devices and choose the correct adapter.


参考答案：B

第8题：

Which cfgmgr flag will display additional information during device configuration?()

A.cfgmgr -a

B.cfgmgr -v

C.cfgmgr -x

D.cfgmgr -o


参考答案：B

第9题：

After using the alt_disk_install command to clone a system image to another disk, the system administrator noticed a large number of defined devices not allocated to the LPAR. Which of the following is the most likely cause of this situation?（）

  • A、The cfgmgr command was not run to reconfigure the devices
  • B、The machine was not booted into SMS MultiBoot mode after configuration
  • C、The machine was not in full system partition mode when the volume was created
  • D、The alt_disk_install command was not run with the -O option to remove references in the ODM

正确答案:D

第10题：

While configuring a new adapter using cfgmgr, an administrator receives a warning message indicating that some device packages are not installed. Additionally, the adapter displays in the Defined state. Which command will resolve the issue and make the adapter available?（）

  • A、shutdown -Fr
  • B、cfgmgr -i <lpp_source>
  • C、mkdev -l <device_name>
  • D、mknode /dev/<device_name>

正确答案:B

更多相关问题
相关内容