单选题During OSPF adjacency formation, in what state is a router when it is negotiating to be in charge of the database synchronization process?（）A InitB 2WayC ExStartD Exchange

A.A

B.B

C.C

D.D

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

A.A

B.B

C.C

D.D

A. RTA will not establish an OSPF adjacency w ith RTB

B. RTA will send OSPF hello packets, but will not send OSPF updates

C. RTA will not accept OSPF hello packets from RTB

D. RTA will send OSPF updates, but will not establish an adjacency with RTB

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

A. Init

B. 2Way

C. ExStart

D. Exchange

You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.What could be the cause of this problem?（）

A. OSPF authentication errors between some of the routers

B. Two routers have the same OSPF router ID

C. Issues with mistuned OSPF timers

D. OSPF LSA pacing issues between some of the routers

E. OSPF neighbor adjacency problems between some of the routers

A.A

B.B

C.C

D.D

A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.

B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.

C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.

D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.

E. The Hello parameters on routers R1 and R2 do not m atch.

A.exstart state>exchange state>loading state>full state

B.exstart state>full state>loading state>exchange state

C.Loading state>exchange state>full state>exstart state

D.exstart state>loading state>exchange state>full state