CMS专题

多选题Which three must be configured for the Packet Capture tool to collect all required data? ()(Choose three.)AEnter the password.BModify the delete time to 3 hours.CSet the interface to local, remote or both.DIncrease the snap length of the Packet Capture

题目
多选题
Which three must be configured for the Packet Capture tool to collect all required data? ()(Choose three.)
A

Enter the password.

B

Modify the delete time to 3 hours.

C

Set the interface to local, remote or both.

D

Increase the snap length of the Packet Capture configuration.

E

Set the Packet Capture size to greater than the actual data flow

如果没有搜索结果,请直接 联系老师 获取答案。
如果没有搜索结果,请直接 联系老师 获取答案。
相似问题和答案

第1题:

Which three BGP attributes are always communicated in a BGP update packet? ()(Choose three.)

A.MED

B.Origin

C.AS Path

D.Next Hop

E.Aggregator


参考答案:B, C, D

第2题:

Which of the following is not an essential prerequisite for AutoQoS to be correctly applied to aninterface? (Choose all that apply.)()

  • A、The interface must be configured as a Multilink PPP interface
  • B、The correct bandwidth should be configured on the interface
  • C、A QoS policy must not be currently attached to the interface
  • D、CEF must be enabled
  • E、AutoQoS must be enabled globally before it can be enabled on the interface
  • F、An IP address must be configured on the interface if its speed is equal to or less than 768 kbps

正确答案:A,E

第3题:

Which three statements are correct about Rate Limiters? ()(Choose three.)

A. one-rate rate limiters

B. two-rate rate limiters

C. two-rate rate limiters is the default

D. one-rate rate limiters is the default

E. there is no default it must be configured


参考答案:A, B, C

第4题:

Which three IP multicast group concepts are true? (Choose three.) ()

  • A、 If a packet is sent to a multicast group address, all members of the multicast group will receive it
  • B、 If a packet is sent to a multicast group address, the multicast frame contains the source multicast  address
  • C、 A router does not have to be a member of a multicast group to receive multicast data.
  • D、 A router does not have to be a member of a multicast group to send to the group.
  • E、 A router must be a member of a multicast group to receive multicast data.
  • F、 A router must be a member of a multicast group to send to the group.

正确答案:A,D,E

第5题:

What is true about a Bypass Tunnel in MPLS Fast Reroute?()

  • A、Only configured on the egress router
  • B、Only configured on the ingress router
  • C、Is pre-signalled to reduce packet loss
  • D、Must intersect the primary LSP at two locations

正确答案:D

第6题:

Which three must be configured for the Packet Capture tool to collect all required data? ()(Choose three.)

A. Enter the password.

B. Modify the delete time to 3 hours.

C. Set the interface to local, remote or both.

D. Increase the snap length of the Packet Capture configuration.

E. Set the Packet Capture size to greater than the actual data flow


参考答案:A, C, E

第7题:

Which of the following are true about SSIDs configured in the ADU?()

  • A、SSIDs are not case sensitive.
  • B、SSIDs must be listed in the same order in the ADU as they are in the access point.
  • C、A maximum of three SSIDs may be configured.
  • D、SSIDs may have a maximum of 16 characters.

正确答案:C

第8题:

What is true about a Bypass Tunnel in MPLS Fast Reroute?()

A. Only configured on the egress router

B. Only configured on the ingress router

C. Is pre-signalled to reduce packet loss

D. Must intersect the primary LSP at two locations


参考答案:D

第9题:

Which three of these statements about the IP service level agreement (SLA) sender are true? ()

  • A、SLA sender target can be an IP host
  • B、SLA sender sends a probe packet and a response probe packet
  • C、SLA sender sends a probe packet
  • D、SLA sender target must be a router
  • E、SLA sender target can be an IP SLA responder

正确答案:A,C,E

第10题:

When configuring unified ports on a 5548 switch, which port ordering must be respected?()

  • A、 Fibre Channel ports must be configured from the first port in the module.
  • B、 Ethernet ports must be configured from the last port in the module.
  • C、 Fibre Channel ports must be configured from the last port in the module.
  • D、 Ethernet ports must be configured from the first port in the module.

正确答案:C,D

更多相关问题