The show ip ospf neighbors command lists two neighbors off Fa0/0.
The show ip ospf neighbors command lists four neighbors off Fa0/0.
The show ip ospf neighbors command lists two neighbors off Fa0/0 in the FULL state.
The show ip ospf neighbors command lists two neighbors off Fa0/0 in the DISCO state.
第1题:
A. Kilobits/seconD
B. Tens of microseconds
C. Cost
D. Hop count
E. No unit is assigneD
第2题:
Refer to the exhibit. When you examine the routing table of R1 and R4, you are not able to see the R1 Ethernet subnet on the R4 routing ta ble. You are also not able to see the R4 Ethernet subnet on the R1 routing table.Which configuration change should be made to resolve this issue? Select the routers where the configuration change will be required, and select the required EIGRP configur ation command(s).()
A. R1 and R4
B. R2 and R3
C. ip summary-address eigrp 1 10.1.1.0 255.255.255.0 and ip summary - address eigrp 110.2.2.0 255.255.255.0
D. variance 2
E. eigrp stub connected
F. no auto - summary
第3题:
A. Performs switching and routing duties
B. A router that directly connects to a switch
C. A multi-purpose switch fabric used in full mesh environments
D. A switch that directly connects to a router
第4题:
R1 is internal to area 1, and R2 is internal to area 2. Subnet 10.1.1.0/24 exists in area 2 as a connected subnet off R2. ABR ABR1 connects area 1 to backbone area 0, and ABR2 c onnects area 0 to area 2. Which of the following LSAs must R1 use when calculating R1's best route for 10.1.1.0/24?()
第5题:
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP. Which one of the following is true?()
第6题:
On Router R1, process EIGRP 1 is redistributing routes from process OSPF 2, calling route - map fred with the redistribute ospf 2 command. R1 has learned intra - area routes for 10.1.1.0/24 and10.1.2.0/24 in part due to the Type 2 LSAs known for each subnet. The route map filters route 10.1.1.0/24 and allows 10.1.2.0/24 througH.Which of the following co mmands on router R1 list subnet 10.1.1.0/24?()
A. show ip route
B. show ip eigrp topology
C. show ip ospf topology
D. show ip eigrp topology 10.1.1.0/24
第7题:
第8题:
某网络拓扑结构如下:在路由器R2上采用show ip rout命令得到如下所示结果。 R2> ... R 192.168.2.0/24[120/1] via 61.114.112.1,00:00:11,Serial2/0 C 192.168.1.0/24 is directly connected,FastEthernet0/0 61.114.112.0/30 is subnetted,1 subnets C 61.114.112.0 is directly connected,Serial2/0 R2> 则host1可能的IP地址为( ),路由器R1的S2/0口的IP地址为( )。
A.192.168.2.1B.192.168.1.1C.61.114.112.1D.61.114.112.2A.192.168.2.1B.192.168.1.1C.61.114.112.1D.61.114.112.2
第9题:
R1, an ABR between backbone area 0 and area 1, has intra - area routes in area 0 for 10.1.1.0/24,10.1.2.0/24, and 10.1.3.0/24. These routes have metrics of 21, 22, and 23, respectively. An engineer then adds the area 0 r ange 10.1.0.0 255.255.0.0 command under the OSPF process of R1. Which of the following is true?()
第10题:
In which of the following scenarios would the "show cdp neighbors detail"command be an appropriate troubleshooting tool?()