端口正常
连接故障,路由器未接到LAN上
接口故障
接口被人为地关闭
第1题:
A. Quidway#show qos-interface priority-queue
B. Quidway#show queueing priority
C. Quidway#show qos-interface ethernet 0 priority-queue
D. Quidway#show qos-interface ethernet 0
第2题:
A.[Quidway]stp port Ethernet0/1 cost cost
B.[Quidway]stp cost cost
C.[Quidway-Ethernet0/1]stp port Ethernet0/1 cost cost
D.[Quidway-Ethernet0/1]stp cost cost
第3题:
路由器上,命令“show int s0”的显示结果为:Serial0 is up,line protocol is down出现该结果的可能原因是()
A.端口处于关闭状态
B.物理端口被烧毁
C.两端设备协议不一致
D.路由表中无路由
第4题:
A. [Quidway-Ethernet0] qos cq cql 10
B. [Quidway-Ethernet0] qos cql 10
C. [Quidway-Ethernet0] access-group 10
D. [Quidway-Ethernet0] acl 10
第5题:
A.[Quidway]stp disable Ethernet0/1
B.[Quidway]stp disable
C.[Quidway-Ethernet0/1]stp disable
D.[Quidway-Ethernet0/1]stp disable all
第6题:
在华为Quidway系列路由器上顺序执行下列命令建立第1组优先列表,
1. Quidway(config)#priority-list 1 interface ethernet0 high
2. Quidway(config)#priority-list 1 interface ethernet0 medium
3. Quidway(config)#priority-list 1 interface ethernet0 normal
4. Quidway(config)#priority-list 1 interface ethernet0 low
在该路由器Ethernet 1接口执行命令“Quidway (config-if_Ethernet1)#priority-group 1”,则接口Ethernet1会将来自于接口Ethernet 0的报文放入( )队列。
A. high
B. medium
C. Normal
D. Low
第7题:
A.[Quidway]stp port Ethernet0/1 priority priority
B.[Quidway]stp priority priority
C.[Quidway-Ethernet0/1]stp priority port Ethernet0/1 priority
D.[Quidway-Ethernet0/1]stp port priority priority
第8题:
A.端口正常
B.连接故障,路由器未接到LAN上
C.接口故障
D.接口被人为地关闭
第9题:
在交换机SWA上执行 display vlan 2 命令后,交换机输出如下:
display vlan 2
VLAN ID: 2
VLAN Type: static
Route interface: not configured
Description: VLAN 0002
Tagged Ports: none
Untagged Ports:
Ethernet1/0/1 Ethernet1/0/3 Ethernet1/0/4
从以上输出可以判断______。
A. 端口 Ethernet1/0/1是一个Trunk 端口
B. VLAN2 中包含了端口Ethernet1/0/1、Ethernet1/0/3 和 Ethernet1/0/4
C. 带有 VLAN2 标签的数据帧离开端口Ethernet1/0/3 时需要剥离标签
D. 当前交换机存在的 VLAN 只有VLAN2
第10题:
在Cisco路由器上如何查看一个以太口(如Ethernet0)的丢包率,收到和发送的包数,字节数?()