CMS专题

单选题What is the default configuration file used by the syslogd daemon?()A/etc/syslog.h B/etc/syslog.pid C/usr/sbin/syslogd D/etc/syslog.conf

题目
单选题
What is the default configuration file used by the syslogd daemon?()
A

 /etc/syslog.h 

B

 /etc/syslog.pid 

C

 /usr/sbin/syslogd 

D

 /etc/syslog.conf

如果没有搜索结果,请直接 联系老师 获取答案。
如果没有搜索结果,请直接 联系老师 获取答案。
相似问题和答案

第1题:

What is the default configuration file used by the sendmail command?()

A. /etc/rc/rc.mail

B. /etc/mail.config

C. /etc/sendmail.config

D. /etc/mail/sendmail.cf


参考答案:D

第2题:

Refer to the exhibit. What can be determined about the router from the console output?()

A.No configuration file was found in NVRAM.

B.No configuration file was found in flash.

C.No configuration file was found in the PCMCIA card.

D.Configuration file is normal and will load in 15 seconds.


参考答案:B

第3题:

What will a new Ezonexam router do during startup if a configuration file is not located in NVRAM?

A.It will search for the configuration file in the locations specified by boot system commands.

B.It will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.

C.It will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.

D.It will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.

E.It will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.


正确答案:C
解析:Explanation:WhenarouterbootsandisabletolocatetheIOSitbeginstoloadtheconfigurationfile.Theconfigurationfile,savedinNVRAM,isloadedintomainmemoryandexecutedonelineatatime.Theseconfigurationcommandsstartroutingprocesses,supplyaddressesforinterfaces,andsetmediacharacteristics.IfnoconfigurationfileexistsinNVRAM,therouterattemptsanetworkbootandsendsabroadcastrequestforthefileonaTFTPserver.Ifthisisalsonotfound,theoperatingsystemexecutesaquestion-driveninitialconfigurationroutinecalledthesystemconfigurationdialog.

第4题:

What will a router do during startup if a configuration file is not located in NVRAM?()

  • A、it will search for the configuration file in the locations specified by boot system commands.
  • B、it will search for the configuration file in flash and if no configuration file is found there, it will enter the setup dialog.
  • C、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will enter the setup dialog.
  • D、it will search for the configuration file in flash and if no configuration file is found there, it will load a limited configuration file from ROM.
  • E、it will search for the configuration file on a TFTP server and if no configuration file is found there, it will load a limited configuration file from ROM.

正确答案:C

第5题:

The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?()

  • A、The command is used to establish a static route.
  • B、The default administrative distance is used.
  • C、The command is used to configure the default route.
  • D、The subnet mask for the source address is 255.255.255.0
  • E、The command is used to establish a stub network

正确答案:A,B

第6题:

The following configuration command was entered into a router:ip route 172.16.3.0 255.255.255.0 192.168.2.4 Which of the following statements are true regarding this configuration change?()

A. The default administrative distance is used.

B. The command is used to establish a static route.

C. The command is used to configure the router interfaces.

D. The command is used to establish a stub network.

E. The subnet mask for the source address is 255.255.255.0


参考答案:A, B

第7题:

Which interface is used to configure debug parameters for log files?()

  • A、Datastore Control Center  
  • B、Alarm and Trace Configuration  
  • C、Custom File Configuration  
  • D、Control Center 

正确答案:B

第8题:

Which account is used to access a Junos device in a factory-default configuration?()

A. root

B. admin

C. juniper

D. user


参考答案:A

第9题:

Which statement is true about the default e-mail address used in the E-mail Subsystem Configuration page? ()

  • A、If no From field is specified with an address in the Send E-mail step, it will use the default.  
  • B、All Send E-mail steps are automatically sent as a Blind cc: to the default.  
  • C、Alarms that are generated by the CRS Server are automatically sent to it.  
  • D、If no e-mail contact is specified in the Create E-mail step, the default is used.

正确答案:A

第10题:

What information does the help reference command provide?()

  • A、A brief description of commands and their default values
  • B、The serial number and version number of the device used to open a support case with JTAC
  • C、A list of all the active hardware alarms on the device
  • D、A display of the current configuration while in operational mode

正确答案:A

更多相关问题