CMS专题
单选题Which parameter， when enabled on a standalone access point， gives the highest priority to a voice packet even when qos is not enabled？（）A igmp snoopingB wmmC qos element for wireless phonesD avvid priority mapping
题目
igmp snooping
wmm
qos element for wireless phones
avvid priority mapping
相似问题和答案
第1题：
Using the WLSE， you are trying to push out a configuration job to a standalone access point， butthe job does not start. Which of the following would cause this failure？（）
- A、invalid parameter in the template
- B、incorrect SNMP communities on the access point
- C、pop-up blocker enabled in the browser
- D、unsupported version of IOS firmware in the access point
正确答案:C
第2题：
Which parameter， when enabled on a standalone access point， gives the highest priority to a voice packeteven when QoS is not enabled？（）
- A、QoS Element for Wireless Phones
- B、IGMP Snooping
- C、WMM
- D、AVVID Priority Mapping
正确答案:A
第3题：
The AirMagnet passive site survey tool can provide RF coverage data， except for which parameter？（）
- A、Signal strength （4th access point）
- B、Signal strength （3rd access point）
- C、Channel interference
- D、Predictive physical data rate downlink （2nd access point）
正确答案:A
第4题：
LWAPP-enabled access points can still communicate with Wireless Domain Services （WDS） devices.
An LWAPP-enabled access point console port provides read-only access to the unit.
LWAPP-enabled access points support Layer 2 LWAPP.
LWAPP-enabled access points must get an IP address and discover the controller using DHCP， DNS， or an IP subnet broadcast.
An LWAPP-enabled access point console port provides read-write access to the unit.
第5题：
You are troubleshooting a problem with a cisco 7920 wireless ip phone on a standalone wlan. the phone rings but， when you Answer ，the call is dropped. What may have caused this problem？（）
- A、publicly secure packet forwarding is enabled.
- B、the minimum data rate is not set to 11 mbps.
- C、an address resolution protocol is enabled.
- D、the access point is set to the least congested channel.
正确答案:A
第6题：
Using the WLSE，you are trying to push out a configuration job to an access point，but the job doesnot start. Which of the following would cause this failure？（）
- A、invalid parameter in the template
- B、incorrect SNMP communities on the access point
- C、unsupported version of IOS firmware in the access point
- D、pop-up blocker enabled in the browser
正确答案:D
第7题：
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped. What may cause this problem？（）
- A、The minimum data rate is not set to 11 Mbps.
- B、An address resolution protocol is enabled.
- C、Publicly Secure Packet forwarding is enabled.
- D、The access point is set to the least congested channel.
正确答案:C
第8题：
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） is failing， butassociation using EAP-PEAP is functioning. What needs to be enabled on the standalone access point tocorrect this issue？（）
- A、a shared key
- B、network EAP
- C、open authentication plus EAP
- D、open authentication plus MAC
正确答案:B
第9题：
On a standalone access point， client association using EAP-Cisco Wireless （Cisco-LEAP） isfailing， but association using EAP-PEAP is functioning. What needs to be enabled on the standalone accesspoint to correct this issue？（）
- A、network EAP
- B、open authentication plus MAC
- C、open authentication plus EAP
- D、a shared key
正确答案:A
第10题：
Transmit only
Diversity
Receive only
Single isolated antenna