CMS专题
多选题Switch R1 and R2 both belong to the Company VTP domain. What’s true about the switch operation in VTP domains？（）AA switch can only reside in one management domainBA switch is listening to VTP advertisements from their own domain onlyCA switch is liste
题目
A switch can only reside in one management domain
A switch is listening to VTP advertisements from their own domain only
A switch is listening to VTP advertisements from multi domains
A switch can reside in one or more domains
VTP is no longer supported on Catalyst switches
相似问题和答案
第1题：
Switch R1 is configured with VTP. Which two VTP modes will make R1 capable of creating and deleting VLANs on itself？ （）
- A、 Client
- B、 Server
- C、 Transparent
- D、 Pass-through
- E、 No-negotiate
正确答案:B,C
第2题：
What action should you execute if you wanted to enable VTP pruning on your entire management domain？（）
- A、 Enable VTP pruning on any client switch in the management domain.
- B、 Enable VTP pruning on any switch in the management domain.
- C、 Enable VTP pruning on every switch in the management domain.
- D、 Enable VTP pruning on a VTP server in the management domain.
- E、 Disable VTP pruning on a VTP server in the management domain.
正确答案:D
第3题：
A.The path of the packets will be R3 to R2 to R1.
B.The path of the packets will be R3 to R1 to R2.
C.The path of the packets will be both R3 to R2 to R1 and R3 to R1.
D.The path of the packets will be R3 to R1
第4题：
What are two results of entering the Switch(config)# vtp mode client command on a Catalyst switch?（）
- A、The switch will ignore VTP summary advertisements.
- B、The switch will forward VTP summary advertisements.
- C、The switch will process VTP summary advertisements.
- D、The switch will originate VTP summary advertisements.
- E、The switch will create, modify and delete VLANs for the entire VTP domain.
正确答案:B,C
第5题：
R1 and R2 are switches that communicate via VTP. What is the default VTP advertisement intervals in Catalyst switches that are in server or client mode？（）
- A、30 seconds
- B、5 minutes
- C、1 minute
- D、10 seconds
- E、5 seconds
- F、None of the other alternatives apply
正确答案:B
第6题：
Two directly connected routers， R1 and R2， are both configured for OSPF graceful restart. R2 is able to switch packets in hardware， but R1 is not. If a network administrator logs on to R2 and performs a system reload， which will be the result？（）
- A、Traffic forwarded from R2 to or through R1 will continue to be forwarded based on the forwarding table state at the time of the reload.
- B、R2 will continue to forward traffic to R1， but R1 will drop the traffic because its neighbor adjacency with R2 has failed.
- C、R2 will continue forwarding traffic to and through R1， but R1 will drop this traffic because it is not capable of maintaining its forwarding state.
- D、All the traffic R2 is forwarding to or through R1 will be dropped while OSPF rebuilds its neighbor adjacency and forwarding tables.
正确答案:A
第7题：
A VTP domain has six active VLANs. Without notice， all VLANs except VLAN1 fail. Just prior tothe failure， Switch2 was added to the network. Which three issues on Switch2 could be the cause？（）
- A、Switch2 is configured for only VLAN1
- B、Switch2 is a VTP server in a different domain
- C、Switch2 is a VTP server in the Company domain
- D、Switch2 is not a VTP domain.
- E、Switch2 has a lower VTP configuration revision number than the current VTP revision
- F、Switch2 has a higher VTP configuration revision number than the current VTP revision
正确答案:A,C,F
第8题：
What is the purpose of the command shown below?vtp password Fl0r1da（）
- A、It is used to validate the sources of VTP advertisements sent between switches.
- B、It is used to access the VTP server to make changes to the VTP configuration.
- C、It allows two VTP servers to exist in the same domain, each configured with different passwords.
- D、It is the password required when promoting a switch from VTP client mode to VTP server mode.
- E、It is used to prevent a switch newly added to the network from sending incorrect VLAN information to the other switches in the domain.
正确答案:A
第9题：
You want to configure switch R1 to propagate VLAN information across the Company network using VTP. What must be configured on a Cisco switch in order to advertise VLAN information？（）
- A、VTP mode
- B、VTP password
- C、VTP revision number
- D、VTP pruning
- E、VTP domain name
- F、None of the other alternatives apply
正确答案:E
第10题：
Switch R1 is configured to use the VLAN Trunking Protocol （VTP）. What does R1 advertise in its VTP domain？（）
- A、The VLAN ID of all known VLANs，the management domain name，and the total number of trunk links on the switch.
- B、The VLAN ID of all known VLANs，a 1-bit canonical format （CF1 Indicator），and the switch configuration revision number.
- C、The management domain name，the switch configuration revision number，the known VLANs， and their specific parameters.
- D、A 2-byte TPID with a fixed value of 0x8100 for the management domain number，the switch configuration revision number，the known VLANs，and their specific parameters.
- E、None of the other alternatives apply.
正确答案:C