CMS专题
单选题VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan3 commmand interface configuration mode？（）A The command is accepted and the respective VLAN is added to vlan dat.B The command is rejected.C The command is a
题目
The command is accepted and the respective VLAN is added to vlan dat.
The command is rejected.
The command is accepted and you must configure the VLAN manually.
The port turns amber.
相似问题和答案
第1题：
A.The route is rejected.
B.The route is accepted.
C.The route is given a lower priority.
D.The route is sent to the default policy.
第2题：
What does the interface subcommand switchport voice vlan 222 indicate？（）
- A、The port is configured for both data and voice traffic.
- B、The port is fully dedicated to forwarding voice traffic.
- C、The port will operate as an FXS telephony port.
- D、Voice traffic will be redirected to VLAN 222.
正确答案:A
第3题：
Thomas: Hey, you look concerned.______
Jack: The final exam. I'm not fully prepared yet.
A、What a lovely day!
B、What has attracted you?
C、What's on your mind?
D、What about seeing the doctor?
第4题：
What happens on failure of a pre or post event script？（）
- A、The error is logged and HA will continue processing
- B、If configured， a recovery command will be run to deal with the problem
- C、An event error is generated and 3 minutes later the cluster will enter config_too_long state
- D、An event error is generated and 6 minutes later the cluster will enter config_too_long state
正确答案:A
第5题：
What is the configured priority value of the Vlan105’s group on DS2 ？（）
- A、 50
- B、 100
- C、 150
- D、 200
正确答案:B
第6题：
A.The command isaccepted and the respective VLAN is added to vlan dat.
B.The command isrejected.
C.The command isaccepted and you must configure the VLAN manually.
D.The port turns amber.
第7题：
VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan3 commmand interface configuration mode？（）
- A、The command is accepted and the respective VLAN is added to vlan dat.
- B、The command is rejected.
- C、The command is accepted and you must configure the VLAN manually.
- D、The port turns amber.
正确答案:A
第8题：
You need to create a new VLAN on your Catalyst switch. This VLAN is to be named EZONEXAM. Which of the following need to be completed for the creation of this new VLAN? (Select all that apply)
A. The EZONEXAM VLAN must be created.
B. The desired ports must be added to the new EZONEXAM VLAN.
C. The EZONEXAM VLAN must be added to all of the domains.
D. The EZONEXAM VLAN must be named.
E. An IP address must be configured for the EZONEXAM VLAN.
F. None of the above. VLAN creations are automatic.
A,B,D 解析：Explanation:
Creating a VLAN is done in 3 steps:
1. Create the VLAN
2. Name the VLAN
3. Assign ports to the VLAN
From there, other features and functionality can be configured, but these are the only steps that are required for the addition of a VLAN.
Incorrect Answers:
C. The VLAN needs only to be added to a single switch, where it can act as a stand-alone VLAN, or it can be transferred to other switches in the network through the use of the VTP protocol.
E. VLANs operate at layer 2, and although many are configured with a layer 3 IP address, it is not absolutely necessary to do this.
第9题：
Hosts on the same VLAN can communicate with each other but are unable to communicate with hosts on different VLANs. What is needed to allow communication between VLANs（）。
- A、a switch with a trunk link that is configured between the switches
- B、a router with an IP address on the physical interface that is connected to the switch
- C、a switch with an access link that is configured between the switches
- D、a router with subinterfaces configured on the physical interface that is connected to the switch
正确答案:D
第10题：
What happens when a route does not match any user configured policies?（）
- A、The route is rejected.
- B、The route is accepted.
- C、The route is given a lower priority.
- D、The route is sent to the default policy.
正确答案:D