多选题Which of the following are characteristics of named access lists?（）AIndividual statements in a named access list may be deleted.BThey require a numbered range from 1000 to 1099.CWhen created, they must be specified as standard or extended.DThey are cre

A. Application of up to three access lists per protocol to a single interface.

B. No more than two access lists per interface.

C. One access list may be configured per direction for each Layer 3 protocol configured on an interface.

D. The maximum number allowed varies due to RAM availability in the router.

E. An infinite number of access lists that can be applied to an interface, from most specific to most general.

F. Cisco IOS allows only one access list to an interface.

A. Router(config)# access-list 1 deny 172.31.212.74 any

B. Router(config)# access-list 1 deny 10.6.111.48 host

C. Router(config)# access-list 1 deny 172.16.4.13 0.0.0.0

D. Router(config)# access-list 1 deny 192.168.14.132 255.255.255.0

E. Router(config)# access-list 1 deny 192.168.166.127 255.255.255.255

Your ERX Edge Router is using an inbound route-map for an EBGP peer to only accept routes in the range of 192.168.32.0 through 192.168.95.255. The route-map references an access list named test .What accurately accomplishes the goal of the route-map?（）

A. access-list test 192.168.32.0 0.0.63.255

B. access-list test permit 192.168.32.0 0.0.64.255

C. access-list test permit 192.168.32.0 0.0.63.255

D. access-list test permit 192.168.32.0 255.255.63.0

An access list was written with the four statements shown in the graphic.Which single access list statement will combine all four of these statements into a single statement that will have exactly the same effect？（）

A.access-list10 permit 172.29.16.00.0.0.255

B.access-list10 permit 172.29.16.00.0.1.255

C.access-list10 permit 172.29.16.00.0.3.255

D.access-list10 permit 172.29.16.00.0.15.255

E.access-list10 permit 172.29.0.00.0.255.255

A. They are always present in the NAT table.

B. They allow connection to be initiated from the outside.

C. They can be configured with access lists, to allow two or more connections to be initiated from the outside.

D. They require no inside or outside interface markings because addresses are statically defined.

You‘re the systems administrator at Testing, and you create the following access control lists.You then enter the command "ip access-group 101 in" to apply access control list 101 to router TK1s e0 interface.Which of the following Telnet sessions will be blocked as a result of your access lists?（）

A. Telnet sessions from host A to host 5.1.1.10

B. Telnet sessions from host A to host 5.1.3.10

C. Telnet sessions from host B to host 5.1.2.10

D. Telnet sessions from host B to host 5.1.3.8

E. Telnet sessions from host C to host 5.1.3.10

F. Telnet sessions from host F to host 5.1.1.10

A. You can delete individual statements in a named access list

B. Named access lists require a numbered range from 1000 to 1099.

C. Named access lists must be specified as standard or extended.

D. You can use the ip access-list command to create named access lists.

E. You cannot delete individual statements in a named access list.

F. You can use the ip name-group command to apply named access lists.

A. Individual statements in a named access list may be deleted.

B. They require a numbered range from 1000 to 1099.

C. When created, they must be specified as standard or extended.

D. They are created with the ip access-list command.

E. The entire access list must be deleted before editing.

F. They are applied with the ip name-group command.

A.you can apply multiple access lists with the same protocol or in different…

B.you can config one access list,per direction,per layer 3 protocol

C.you can placeasmanyaccess lists as you want on any interface

D.you can apply ony one access list on any interface