儿科护理专业实践能力
单选题What will happen if you issue the redundancy force-switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? （）A reset of the primary supervisorB manual switchover from standby to active supervisorC manual switchover from ac
题目
reset of the primary supervisor
manual switchover from standby to active supervisor
manual switchover from active to standby supervisor
automatic switchover from active to standby on primary supervisor failure
相似问题和答案
第1题：
A. reset of the primary supervisor
B. manual switchover from standby to active supervisor
C. manual switchover from active to standby supervisor
D. automatic switchover from active to standby on primary supervisor failure
第2题：
A. reset of the primary supervisor
B. manual switchover from standby to active supervisor
C. manual switchover from active to standby supervisor
D. automatic switchover from active to standby on primary supervisor failure
第3题：
A. Three physical interfaces are redundant.
B. You must define an additional Redundancy Group.
C. node 0 will immediately become primary in the cluster.
D. You must issue an operational command and reboot the system for the above configuration to take effect.
第4题：
What is the correct sequence of commands to configure and verify SRM with SSO redundancy? （）
- A、mode sso, redundancy, show redundancy states
- B、show redundancy states, mode sso, redundancy
- C、redundancy, mode sso, show redundancy states
- D、show redundancy states, redundancy, mode sso
正确答案:C
第5题：
You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be a roaming bandwidth issuE. in order to verify what kind of issue it is， you decide to increase the bandwidth reserved for roaming on the wlan controller to the maximum. What level do you set the bandwidth to？（）
- A、25 percent
- B、15 percent
- C、5 percent
- D、35 percent
正确答案:A
第6题：
A. mode sso, redundancy, show redundancy states
B. show redundancy states, mode sso, redundancy
C. redundancy, mode sso, show redundancy states
D. show redundancy states, redundancy, mode sso
第7题：
As an experienced technician, you are required to configure and verify SRM with SSO redundancy. In such a situation, you have to issue several commands in proper orders. Which of the following is correct?（）
- A、show redundancy states, redundancy, mode sso
- B、show redundancy states, mode sso, redundancy
- C、redundancy, mode sso, show redundancy states
- D、mode sso, redundancy, show redundancy states
正确答案:C
第8题：
As an experienced technician, you are required to configure and verify SRM with SSO redundancy. In such a situation, you have to issue several commands in proper orders. Which of the following is correct?（）
A. show redundancy states, redundancy, mode sso
B. show redundancy states, mode sso, redundancy
C. redundancy, mode sso, show redundancy states
D. mode sso, redundancy, show redundancy states
第9题：
You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）
- A、IEEE 802.10
- B、Misconfigured NIC
- C、User configuration
- D、IEEE 802.1Q
- E、None of the other alternatives apply
正确答案:D
第10题：
When applying the configuration in the exhibit and initializing a chassis cluster， which statement is correct？（） [edit chassis] user@host# show cluster { reth-count 3； redundancy-group 1 { node 0 priority 1； node 1 priority 100； } }
- A、Three physical interfaces are redundant.
- B、You must define an additional redundancy group.
- C、node 0 will immediately become primary for redundancy group 1.
- D、You must issue an operational command and reboot the system for the above configuration to take effect.
正确答案:D