JN0-102
单选题You issue the command telnet interface ge-1/1/0 10.10.10.1 source 192.168.100.1 bypass-routing. Which statement is correct?（）A The bypass-routing parameter is ignored when using private IP addressing.B The telnet session will have the source IP address
题目
The bypass-routing parameter is ignored when using private IP addressing.
The telnet session will have the source IP address 10.10.10.1.
The telnet session will connect to the neighboring device's interface ge-1/1/0.
Return traffic for the telnet session might not arrive at interface ge-1/1/0.
参考答案和解析
相似问题和答案
第1题：
A. The count parameter creates a counter that you can view with the show firewall command
B. The count parameter allows the router to count the number of pings for logging purposes
C. The count parameter allows the router to pause for 10000 seconds before sending out a ping
D. The count parameter allows the router to send out 1000 pings and then stop
第2题：
Which of the following descriptions about IP spoofing is correct？（）
- A、IP source address is forged
- B、IP destination address is forged
- C、IP TCP source port is forged
- D、IP TCP destination port is forged
- E、None of above
正确答案:A
第3题：
A. The count parameter creates a counter that you can view with the show firewall command.
B. The count parameter allows the router to count the number of pings for logging purposes.
C. The count parameter allows the router to pause for 1000 seconds before sending out a ping.
D. The count parameter allows the router to send out 1000 pings and then stop.
第4题：
You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
- A、The count parameter creates a counter that you can view with the show firewall command
- B、The count parameter allows the router to count the number of pings for logging purposes
- C、The count parameter allows the router to pause for 10000 seconds before sending out a ping
- D、The count parameter allows the router to send out 1000 pings and then stop
正确答案:D
第5题：
When using the Cisco SDM Quick Setup Siteto-Site VPN wizard， which three parameters do you configure？（）
- A、Source interface where encrypted traffic originates
- B、IP address for the remote peer
- C、Transform set for the IPsec tunnel
- D、Interface for the VPN connection
正确答案:A,B,D
第6题：
A. The bypass-routing parameter is used to test the density on the TI line.
B. The bypass-routing parameter cannot be used on a T1 interface.
C. The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
D. The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic
第7题：
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
- A、The crypto ACL number
- B、The IPSEC mode （tunnel or transport）
- C、The GRE tunnel interface IP address
- D、The GRE tunnel source interface or IP address， and tunnel destination IP address
- E、The MTU size of the GRE tunnel interface
正确答案:C,D
第8题：
You have two IP addresses configured on the ge-0/0/6 interface, as shown in the exhibit. You want to select the 172.16.10.101 address as the source address for packets sent from this interface to hosts on a remote subnet.Which parameter would you add to the 172.16.10.101 address to complete this task?（）
A. preferred
B. broadcast
C. primary
D. arp 172.16.10.101
第9题：
Which of the following statements are true concerning the command ip sla monitor responder typetcpconnect ipaddress 10.1.1.1 port 23？（Choose all that apply.）（）
- A、The command will initiate a probe with a destination IP address of 10.1.1.1
- B、The command is used on the IP SLA responder and the IP SLA source
- C、The command will allow only source address 10.1.1.1 to source probes
- D、The command will initiate a probe with a destination Telnet port
- E、The command is used to make the router a responder
- F、The command will initiate a probe with a source port of 23
正确答案:A,D
第10题：
You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）
- A、The count parameter creates a counter that you can view with the show firewall command.
- B、The count parameter allows the router to count the number of pings for logging purposes.
- C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.
- D、The count parameter allows the router to send out 1000 pings and then stop.
正确答案:D