思科认证考试

You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）A、The Frame Relay encapsu

题目

You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）

  • A、The Frame Relay encapsulation on the physical interface.
  • B、The local DLCI on each subinterface.
  • C、An IP address on the physical interface.
  • D、The subinterface type as point-to-point.
如果没有搜索结果，请直接 联系老师 获取答案。
如果没有搜索结果，请直接 联系老师 获取答案。
相似问题和答案

第1题：

You are trying to bring up a new Testking location onto your existing frame relay network. The new location is using an Adtran router and you are having difficulties getting the site to connect via frame to your Cisco HQ router. What is the most likely cause of the problem?（）

A. Mismatched LMI types.

B. Incompatible encapsulation types.

C. Mismatching IP addresses.

D. Incorrect DLCI.

E. None of the above


参考答案：B

第2题：

Which of the following Frame－Relay encapsulation commands would you use, if you had to connect your Cisco router to a non－Cisco router?()

A. TestKRouter(config-if)# Encapsulation frame-relay dot1q

B. TestKRouter(config-if)# Encapsulation frame-relay aal5snap

C. TestKRouter(config-if)# Encapsulation frame-relay ietf

D. TestKRouter(config-if)# Encapsulation frame-relay isl

E. None of the above


参考答案：C

第3题：

Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()

A. frame-relay arp

B. frame-relay map

C. frame-relay interface-dlci

D. frame-relay lmi-type


参考答案：B

第4题：

which command allows you to verify the encapsulation type (CISCO OR IETF) for a frame relay link?()

A.show frame-relay map

B.show frame-relay lmi

C.show inter serial

D.show frame-relay pvc


参考答案：C

第5题：

When configuring Frame Relay using point－to－point subinterfaces, which of the following must not be configured?()

A. The local DLCI on each subinterface of the Frame Relay.

B. The Frame Relay encapsulation on the physical interface.

C. An IP address on the physical interface.

D. The subinterface type as point-to-point


参考答案：C

第6题：

You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()

A. Show interface lmi

B. Show frame-relay lmi

C. Show interface frame-relay

D. Debug frame-relay interface.


参考答案：B

第7题：

A new frame－relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?()

A. frame-relay arp

B. frame-relay map

C. frame-relay interface-dlci

D. frame-relay lmi-type

E. frame-relay pvc


参考答案：B

第8题：

In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）

A. The IP addresses are configured incorrectly.

B. Frame Relay LMI messages not displayed in real time.

C. The administrator must issue the enable frame-relay lmi debug command.

D. The administrator must issue the terminal monitor command.

E. Debug messages can only be received once through the console port.

F. The administrator must issue the show frame-relay lmi vty 0 4 command


参考答案：D

第9题：

You are implementing a new frame relay network to provide connectivity between you offices. To do this, you set up the frame relay network using point-to-point subinterfaces.Which of the following does NOT need to be configured?（）

A. The Frame Relay encapsulation on the physical interface.

B. The local DLCI on each subinterface.

C. An IP address on the physical interface.

D. The subinterface type as point-to-point.


参考答案：C

第10题：

When should traffic shaping be implemented on Frame Relay PVCs？（）

  • A、When you want to drop excess traffic above the CIR
  • B、When there is a speed mismatch between the central site and the remote site
  • C、When using Frame Relay SVCs
  • D、When over-subscribing the central site link
  • E、When LLQ is implemented on the Frame Relay PVC
  • F、When Multilink PPP LFI is implemented on the Frame Relay PVC

正确答案:B,D

更多相关问题
相关内容