思科认证考试

What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）A、reset of the primary supervisorB、manual switchover from standby to active supervisorC、manual switchover from active

题目

What will happen if you issue the redundancy force-switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?（）

  • A、reset of the primary supervisor
  • B、manual switchover from standby to active supervisor
  • C、manual switchover from active to standby supervisor
  • D、automatic switchover from active to standby on primary supervisor failure
如果没有搜索结果，请直接 联系老师 获取答案。
如果没有搜索结果，请直接 联系老师 获取答案。
相似问题和答案

第1题：

What will happen if you issue the redundancy force－switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? ()

A. reset of the primary supervisor

B. manual switchover from standby to active supervisor

C. manual switchover from active to standby supervisor

D. automatic switchover from active to standby on primary supervisor failure


参考答案：C

第2题：


What will happen on May 10th?
A. Another seminar will be held.
B. Mr. Takagi and Ms. Lee will meet.
C. The seminar will end.
D. Mr. Takagi，Ms. Lee and Ms. Ward will meet.


答案：D
解析：
Takagi给Ward写的邮件中的下半部分中提到5月10号见面，并说届时，Lee也会参加这次会面。因此可以推知TakagKWard.Lee会在5月10号这一天会面。正确答案是D。

第3题：

Desk Clerk:Good afternoon,Holiday Inn.Customer:Hello,I’d like to book a double room for the nights of 23rd and 24th please. Desk Clerk:______

A:What’s the matter?

B:Just a minute, please.

C:What can I do for you?

D:Can I help you?


参考答案：B

第4题：

You delete a trace options file and later notice that no new entries are being written to this file. What would allow the entries to be written to the file again?（）

  • A、Issue a commit of the current configuration.
  • B、Issue a commit full of the current configuration.
  • C、Issue a commit all of the current configuration.
  • D、Issue a commit confirmed of the current configuration.

正确答案:B

第5题：

You need to troubleshoot an issue on the switched LAN. When you issue a command "show port3/1" on a switch， you observe the Giants column has a non-zero entry. What could cause this？（）

  • A、IEEE 802.10
  • B、Misconfigured NIC
  • C、User configuration
  • D、IEEE 802.1Q
  • E、None of the other alternatives apply

正确答案:D

第6题：

What will happen if you issue the redundancy force－switchover command on a Catalyst 6500Series Switch with redundant supervisor modules?()

A. reset of the primary supervisor

B. manual switchover from standby to active supervisor

C. manual switchover from active to standby supervisor

D. automatic switchover from active to standby on primary supervisor failure


参考答案：C

第7题：

You are troubleshooting a problem with a cisco 7920 wireless ip phone that is causing the phone to drop calls. the problem appears to be a roaming bandwidth issuE.  in order to verify what kind of issue it is， you decide to increase the bandwidth reserved for roaming on the wlan controller to the maximum. What level do you set the bandwidth to？（）

  • A、25 percent
  • B、15 percent
  • C、5 percent
  • D、35 percent

正确答案:A

第8题：

If the derrick is overloaded, what will happen?


正确答案：The cargo wire or the derrick will break up, and maybe hurt persons.

第9题：

While working in setup mode, a configuration line is typed incorrectly. What should you do to exit setup mode, without executing or saving any of the mistakes you made?（）

  • A、Type exit at the setup dialog.
  • B、Type close at the setup dialog.
  • C、Press the Ctrl-C key combination.
  • D、Press the Ctrl-X key combination.
  • E、Issue the copy startup-config command.
  • F、Issue the 'write e" command.
  • G、Issue the "write mem" command

正确答案:A,C

第10题：

You have backed up your database twice without connecting to the recovery catalog. What command do you issue to transfer the control-file metadata to the recovery catalog？（）

  • A、 synch catalog
  • B、 resync catalog
  • C、 replicate catalog
  • D、 update catalog
  • E、 restore catalog

正确答案:B

更多相关问题
相关内容