思科认证考试
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configu
题目
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1
- A、EIGRP works on F0/0 and S0/0/0 without further configuration
- B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE
- C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE
- D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1
相似问题和答案
第1题：
A. Metric
B. Administrative distance
C. Timeout (seconds)
D. Prefix length
E. Interface ID
第2题：
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）
A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0
B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0
C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0
D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0
E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0
F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
第3题：
在[问题1]和[问题2]中，所使用的是静态路由协议。当该公司有多个分支机构，决定使用动态路由协议OSPF。下面是分支机构路由器R1的配置命令列表，在空白处填写合适的命令/参数，实现R1的正确配置。(注：点对点链路的area为2，分支机构局域网的area为3)。
R1＞en
R1conf term
R1(config)no ip route
R1(config)router [ (6) ]
R1(config-router)network[ (7) ]area 2
R1(config-router)network[ (8) ]area 3
R1(confiq-router)exit
R1copy run start
(6)OSPF 100(注：100为OSPF进程号，可为1～65535之间的任意整数) (7)192.168.15.0 0.0.0.3 (8)192.168.16.0 0.0.0.31 解析：所在的命令的作用是启用OSPF进程，因此该处因填写“OSPF进程ID＞”：空(7)和空(8)所在的命令的作用是指定与R1路由器相连的网络。该路由器相连两个网络，一个是192.168.15.0/30，另一个是192.168.16.0/27。但需要注意的是network命令中使用的不是予网掩码，而是wildcard-mask，它是子网掩码的反码，可以用255.255.255.255减去予网掩码求得。因此空(7)处应填写“192.168.15.0 0.0.0.3”：空(8)处应填写“192.168.16.0 0.0.0.31”。
第4题：
A. Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised.
B. Router R1 will advertise both rou tes.
C. Router R1 should be reconfigured with an ACL instead of an ip prefix - list command.
D. Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.
第5题：
A. Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks.
B. Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1.
C. Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2.
D. Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2.
E. The Hello parameters on routers R1 and R2 do not m atch.
第6题：
Router R1 has a connected route for 10.1.1.0/24 off interface Fa0/0. Interface Fa0/0 has been enabled for OSPF due to a router ospf 1 and network 10.0.0.0 0.0.0.255 area 0 command. R1 also has EIGRP configured, with the redistribute ospf 1 metric 1000 100 10 1 1500 command configured under EIGRP.Which one of the following is true?（）
A. R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route.
B. For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth.
C. For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay.
D. No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
第7题：
Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）
A. Add the area 1 stub command on routers R1.
B. Add the always keyword to the default - information originate configuration command on router R2.
C. Remov e the default information originate configuration command from router R2 and place it on router R1.
D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.
第8题：
以下是路由器R1的部分配置，请完成其配置，或解释配置命令含义。
!
R1 (Config) interface fastethernet0
R1(Config-if) ip address (6) (7)
R1(Config-if) (8) (开启端口)
!
R1 (Config) interface serial 0
R1(Config-if) ip address (9) (10)
!
R1 (Config) ip routing
R1 (Config) router rip (11)
R1 (Config-router) (12) (声明网络)
R1 (Config-router) (13) (声明网络)
R1 (Config-router) (14) (声明网络)
R1 (Config-router) version 2 (15)
!
(6)192.168.1.1 (7)255.255.255.0 (8)noshutdown (9)192.168.251.1 (10)255.255.255.0 (11)进入RIP配置模式 (12)network 192.168.1.0 (13)network 192.168.251.0 (14)network 192.168.253.0 (15)设置RIP协议版本2 注：(12)、(13)、(14)答案可互换 解析：由上图可知，路由器R1的e0的地址为192.168.1.1/24，s0的地址为192.168.251.1/24，使用network命令声明网络，分别是192.168.1.0、192.168.251.0、192.168.253.0。所以其配置应如下。
!
R1(Config)#interface fastethernet0
R1(Config-if) #ip address192.168.1.1255.255.255.0
R1(Config-if)# noshutdown (开启端口),
!
R1(Config)#interface serial 0
R1(Config-if)# ip address 192.168.251.1 255.255.255.0
!
R1(Config)# ip routing
R1 (Config) #router rip(进入RIP配置模式)
R1(Config-router)# network 192.168.1.0(声明网络 192.168.1.0/24)
R1(Config-router)# network 192.168.251.0(声明网络 192.168.251.0/24)
R1(Config-router)# network 192.168.253.0(声明网络 192.168.253. 0/24)
R1(Config-router) #version 2 (设置RIP协议版本2)
第9题：
A. Router R2 will be preferred because it has the higher neighbor IP address.
B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.
C. Router R1 will be preferred because it has a lower local preference.
D. Router R2 will be preferred because it has a higher local preference.
E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.
F. Router R1 will be preferred because it has the lower neighbor IP address.
第10题：
A. The no auto - summary command has not been issued under the EIGRP process on both routers.
B. Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24.
C. EIGRP cannot exchange routing updates with a neighbor‘s router interface that is configured with tw o IP addresses.
D. EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.