You want to allow Router R1 to immediately become the active router if its priority is highest than the active router fails. What command would you use if you wanted to configure this? ()
第1题:
A. reset of the primary supervisor
B. manual switchover from standby to active supervisor
C. manual switchover from active to standby supervisor
D. automatic switchover from active to standby on primary supervisor failure
第2题:
In a GLBP network, who is responsible for the arp request?()
第3题:
As a network administrator, you have configured a Catalyst 6500 Series Switch with redundant supervisor engine in a CIS network. What is the result of issuing the redundancy force-switchover command on that switch?()
A. Automatic switchover from active to standby on primary supervisor failure
B. Reset of the primary supervisor.
C. Manual switchover from active to standby supervisor
D. Manual switchover from standby to active supervisor
第4题:
What three tasks must a network administrator perform to properly configure Hot Standby Routing Protocol (HSRP)?()
第5题:
Routers R1 and R2 are configured for HSRP as shown below: Router R1: interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2: interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this? ()
第6题:
A. enable cdp
B. cdp enable
C. cdp run
D. run cdp
第7题:
You administer a network that uses two routers, R1 and R2, configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows: R1#configure terminal R1(config)#interface fa0/0 R1(config-if)#ip address 10.10.0.5 255.255.255.0 R1(config-if)#standby 1 priority 150 R1(config-if)#standby preempt delay minimum 50 R1(config-if)#standby 1 track interface fa0/2 15 R1(config-if)#standby 1 ip 10.10.0.20 Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1?()
第8题:
A. reset of the primary supervisor
B. manual switchover from standby to active supervisor
C. manual switchover from active to standby supervisor
D. automatic switchover from active to standby on primary supervisor failure
第9题:
What will happen if you issue the redundancy force-switchover command on a Catalyst 6500 SeriesSwitch with redundant supervisor modules? ()
第10题:
Routers R1 and R2 are configured for HSRP as shown below: Router R1: interface ethernet 0 ip address 20.6.2.1 255.255.255.0 standby 35 ip 20.6.2.21 standby 35 priority 100 interface ethernet 1 ip address 20.6.1.1.2 255.255.255.0 standby 34 ip 20.6.1.21 Router R2: interface ethernet 0 ip address 20.6.2.2 255.255.255.0 standby 35 ip 20.6.2.21 interface ethernet 1 ip address 20.6.1.1.1 255.255.255.0 standby 34 ip 20.6.1.21 standby 34 priority 100 You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice veryfrequent HSRP group state transitions. What is the most likely cause of this?()