多选题Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）AIt is achieved by using more than one HSRP group.BIt is done in regards to either round robin o

第1题：

第2题：

You administer a network that uses two routers， R1 and R2， configured as an HSRP group to  provide redundancy for the gateway. Router R1 is the active router and has been configured as  follows：   R1#configure terminal   R1（config）#interface fa0/0   R1（config-if）#ip address 10.10.0.5 255.255.255.0   R1（config-if）#standby 1 priority 150   R1（config-if）#standby preempt delay minimum 50   R1（config-if）#standby 1 track interface fa0/2 15   R1（config-if）#standby 1 ip 10.10.0.20   Which of the following describes the effect the standby preempt delay minimum 50 command will  have on router R1？（）

• A、 The HSRP priority for router R1 will increase to 200.
• B、 Router R1 will become the standby router if the priority drops below 50.
• C、 The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.  
• D、 Router R1 will wait 50 seconds before attempting to preempt the active router.

第3题：

第4题：

Which of the following HSRP router states does an active router enter when it is preempted by a  higher priority router？（）

• A、 active
• B、 speak
• C、 learn
• D、 listen
• E、 init
• F、 standby

第5题：

What three tasks must a network administrator perform to properly configure Hot Standby Routing  Protocol （HSRP）？（）

• A、 Define the encapsulation type.
• B、 Define the standby router.
• C、 Define the standby IP address.
• D、 Enable the standby priority.

第6题：

You want to allow Router R1 to immediately become the active router if its priority is highest than  the active router fails.  What command would you use if you wanted to configure this？ （）

• A、 en standby preempt
• B、 standby preempt enable
• C、 standby preempt
• D、 hot standby preempt

第7题：

Hot Standby Router Protocol (HSRP) is able to provide network redundancy for IP networks. Concerning HSRP load sharing, which two descriptions make sense?（）

• A、It is achieved by using more than one HSRP group.
• B、It is done in regards to either round robin or weight basis.
• C、It is used to offload the active router in a certain HSRP group.
• D、The return traffic is influenced by HSRP load sharing configuration.
• E、Single group HSRP is used to achieve more efficient link utilization.

第8题：

第9题：

HSRP. Known as Hot Stanclby Router Protocol, is a Cisco proprietarv redundancy protocol . As an experienced network administrator, you are required to configure HSRP on a XYZ network. Which TWO of the following wii be available and shared between the routers configured with HSRP? （）(Choose two.)

• A、a shared single interface
• B、the ability to track serial interfaces
• C、UDP-based hello packets
• D、the impact of flapping links if timers are too low

第10题：

Router R1 and R2 are both configured for HSRP.  Which two statements about the HSRP priorities  of these two routers are true？（）

• A、 To assign the HSRP router priority in a standby group， the standby group-number priority  priority-value global configuration command must be used.
• B、 The default priority of a router is zero （0）.
• C、 The no standby priority command assigns a priority of 100 to the router.
• D、 Assuming that preempting has also been configured， the router with the lowest priority in an  HSRP group would become the active router.
• E、 When two routers in an HSRP standby group are configured with identical priorities， the router  with the highest configured IP address will become the active router.