单选题Refer to the exhibit. A router has a 256 kbps Frame Relay circuit connected to interface serial 0/0. As a large FTP packet is being placed into the hardware transmit queue of interface serial 0/0， a voice packet is placed into the priority queue of tha

Refer to the exhibit. You are the network administrator of the Route.com company. You have been tasked to implement a hub and spoke EIGRP topology over Frame Relay to provide connectivity between the networks at headquarters and all 300 spokes. Before you begin the actual implementation, which three pieces of information are more important to know than the others?（）

A. the Committed Information Rate of all the Frame Relay PVCs

B. the Cisco IOS version running on all the routers

C. the router model number of all the spoke routers

D. the number of HQ networks connected behind the headquarter routers

E. the routing policy, such as whether or not the spokes can be used as backup transient point between the two headquarter routers

A. Router R2 will be preferred because it has the higher neighbor IP address.

B. Router R2 will be preferr ed because its neighbor has a lower autonomous system number.

C. Router R1 will be preferred because it has a lower local preference.

D. Router R2 will be preferred because it has a higher local preference.

E. Router R1 will be preferred because its nei ghbor has the higher autonomous system number.

F. Router R1 will be preferred because it has the lower neighbor IP address.

A. Issue the command bandwidth 224 on the physical interface.

B. Issue the command bandwidth 56 on the physical interface.

C. Issue the command bandwidth 224 on each subinterface.

D. Issue the command bandwidth 56 on each subinterface.

Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other‘s routes. What is the solution?（）

A.Check and change the access lists on router RTA

B.Configure the auto summary command under router eigrp 1 on router RTA

C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface

D.Issue the no ip split horizon command on router RTA

E.Issue the no ip split horizon eigrp 1 command on router RTA

F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers

A. Router RTA is the BDR

B. Router RTA is directly connected to interface 192.168.45.1

C. Neighbor 192.168.45.1 has changed its OSPF priority number

D. Router RTA and neighbor 192.168.45.2 are exchanging OSPF LSAs

A.The router is in area 49.0001.0002

B.The router acts as a Level 1 - 2 router

C.CLNS routing is enable d for the router

D.The router has a system ID of 0003.0004

E.The interfaces have a functional IS - IS configuration

F.The network service access point selector (NSEL) byte has a value of 0

Refer to the exhibit. Router RT - 1 and router RT - 2 both advertise network 131.25.0.0/16 to routerRT - 3 via internal BGP. What is the reason that router RT - 3 chose router RT - 1 as its best path tonetwork 131.25.0.0/16.（）

A. It has a better router ID

B. It advertises a lower autonomous system

C. It advertises t he best AS - path

D. It advertises the best local preference

E. It advertises the best origin code

F. It advertises the best MED

Refer to the exhibit. Two routers are connected by Frame Relay and are running OSPF bet ween them. Each router has been configured with the appropriate network statements under router ospf 1, but the routers are not forming an adjacency. Which of the following three commands could be configured on each router to correct this problem?（）

A. RouterC(config - if)#ip ospf network broadcast RouterD(config - if)#ip ospf network broadcast

B. RouterC(config - if)#ip ospf network point - to - point RouterD(config - if)#ip ospf network point - to - point

C. RouterC(config - router)#neighbor 10.100. 100.4 RouterD(config - router)#neighbor 10.100.100.3

D. RouterC(config - router)#neighbor 10.255.255.254 RouterD(config - router)#neighbor 10.255.255.253

A. Router(config-if)# encapsulation frame-relay q933a

B. Router(config-if)# encapsulation frame-relay ansi

C. Router(config-if)# encapsulation frame-relay ietf

D. Router(config-if)# encapsulation frame-relay isl

E. None of the above

A.Router1 has specific boot system command that instruct it to load IOS from TFTP server.

B.Router1 is acting as a TFTP server for other routers.

C.Router1 cannot locate a valid IOS image in flash memory.

D.Router1 defaulted to ROMMON mode and loaded the IOS image from a TFTP server.

E.Cisco routers will first attempt to load a image from TFTP for management purposes.