单选题After installing a new hard drive into a server for the purpose of mirroring the data from the first drive to the second one， the server displays an “operating system not found” error. Which of the following should the technician do to boot the server 

第1题：

第2题：

A technician has lost a necessary jumper for a new hard drive that must be installed immediately.Which of the following is the BEST solution?（）

• A、Use a jumper from the motherboard where the new drive is going to be installed.
• B、Use a jumper from a hard drive that is no longer functioning.
• C、Contact the manufacturer of the new hard drive and have a replacement jumper shipped immediately.
• D、The new hard drive must be replaced

第3题：

第4题：

A cisco wcs version 4.0 has been installed on a server with a dual pentium 3.0 ghz processor，4 gb ram，and an 80 gb hard drive. a location appliance has been incorporated into the network and is being monitored by the cisco wcs. there are 3000 devices to be tracked but not all of them are being tracked on the cisco wcs. What can be done to correct the problem？（）

• A、add a new location appliance.
• B、add a new cisco wcs server dedicated to the location appliance.
• C、add 4 gb of ram to the cisco wcs.
• D、add a 120 gb hard drive to the cisco wcs.

第5题：

An administrator just installed a new RAID controller card into a server. The firmware is current for the controller card. When the server is powered up the administrator notices that the RAID controller card is not recognized during POST. Which of the following is the cause of the problem？（）

• A、The hard drives were not plugged into the server correctly.
• B、The controller driver is outdated and needs to be updated from the OEMs website.
• C、The firmware for the server is too old and does not support the new RAID controller card.
• D、The cable from the controller to the hard drive backplane is not connected.

第6题：

After performing the initial steps in installing the server OS from a DVD-ROM， the server reboots and goes back into the setup wizard. Which of the following is the MOST likely cause for this problem？（）

• A、The DVD-ROM drive has failed.
• B、An installation file copied from the DVD to the hard drive is corrupt.
• C、Faulty OS installation DVD
• D、Incorrect boot sequence in the BIOS

第7题：

A server has a single failed hard drive in an array that is accessed through a hot plug backplane to ease replacement of failed drives. After replacing the drive several times， each of the replacement drives failed to power up and rebuild as the failed drive.  Which of the following is the MOST likely cause of the failures？（）

• A、 The backplane has failed and needs to be replaced.
• B、 The array must be disbanded and recreated from a backup source to recognize the replacement drive.
• C、 There is a conflict with the optical drive on the server.
• D、 The server power supply is failing and not providing enough power for all the drives.

第8题：

第9题：

A technician purchases a new 120 GB IDE hard disk to use in an old server as a swap drive. After adding the drive to the server， the technician discovers that the operating system does not detect the drive.   After rebooting the server， the technician notices the drive is missing from POST and comes to the conclusion that the BIOS needs to be updated. The technician downloads the latest version of the BIOS update from the manufacturer website.   Which action should the technician take next？（）

• A、 backup the BIOS configuration to use later
• B、 install the BIOS update from a command prompt
• C、 create a bootable floppy and copy the BIOS update tools to the floppy
• D、 read the manufacturer’s guidelines and recommendations on installing the update

第10题：

After setting up a new computer, a user states that the mouse and keyboard will not work. Whichof the following is the MOST likely reason?（）

• A、The network cable is disconnected
• B、The PS/2 connectors are switched
• C、The USB connectors are switched
• D、The hard drive is unplugged