CMS专题

问答题you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC？

题目
问答题
you want to view the status of a frame relay connection. How to display the status of a Frame-Relay PVC？
如果没有搜索结果，请直接 联系老师 获取答案。
如果没有搜索结果，请直接 联系老师 获取答案。
相似问题和答案

第1题：

You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()

A. Show interface lmi

B. Show frame-relay lmi

C. Show interface frame-relay

D. Debug frame-relay interface.


参考答案：B

第2题：

Which command can be used to verify the DLCI destination address in a Frame Relay static configuration?()

A.show frame-relay end-to-end

B.show frame-relay map

C.show frame-relay lmi

D.show frame-relay pvc


参考答案：B

第3题：

You are working with a client to deploy QoS on their Frame Relay WAN. They would like to be able to allow packets to cross the Frame Relay WAN but have them marked as discard eligible if they exceed the QoS policy.How would you accomplish this task?（）

A. Configure a class map that sets the DE bit so that the policy map can correctly apply a violate-action if the policy is exceeded.

B. Configure a service policy that sets the DE bit and apply it to the serial interface connected to the Frame Relay WAN.

C. Configure a policy map that has a burst-max action of setting the DE bit if the policy is exceeded.

D. Configure a policy map that has a violate-action to change the DE bit from 0 to 1.


参考答案：D

第4题：

What does FRTP stand for？（）

  • A、Frame Relay Top Pseudowire
  • B、Frame Relay Traffic Pseudowire
  • C、Frame Relay Traffic Protocol
  • D、Frame Relay Traffic Policing

正确答案:D

第5题：

Which of the following Frame-Relay encapsulation commands would you use, if you had to connect your Cisco router to a non-Cisco router?（）

  • A、TestKRouter(config-if)# Encapsulation frame-relay dot1q
  • B、TestKRouter(config-if)# Encapsulation frame-relay aal5snap
  • C、TestKRouter(config-if)# Encapsulation frame-relay ietf
  • D、TestKRouter(config-if)# Encapsulation frame-relay isl
  • E、None of the above

正确答案:C

第6题：

which command allows you to verify the encapsulation type (CISCO OR IETF) for a frame relay link?()

A.show frame-relay map

B.show frame-relay lmi

C.show inter serial

D.show frame-relay pvc


参考答案：C

第7题：

When should traffic shaping be implemented on Frame Relay PVCs？（）

  • A、When you want to drop excess traffic above the CIR
  • B、When there is a speed mismatch between the central site and the remote site
  • C、When using Frame Relay SVCs
  • D、When over-subscribing the central site link
  • E、When LLQ is implemented on the Frame Relay PVC
  • F、When Multilink PPP LFI is implemented on the Frame Relay PVC

正确答案:B,D

第8题：

Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? ()

A. frame-relay arp

B. frame-relay map

C. frame-relay interface-dlci

D. frame-relay lmi-type


参考答案：B

第9题：

A new frame-relay network is being implemented and inverse ARP does not appear to be operating correctly. Which alternative command can be used to provide connectivity?（）

  • A、frame-relay arp
  • B、frame-relay map
  • C、frame-relay interface-dlci
  • D、frame-relay lmi-type
  • E、frame-relay pvc

正确答案:B

第10题：

In order to troubleshoot an issue with the Testking frame relay network, you log into a remote router via a telnet session and issue the command "debug frame-relay lmi". After a long wait, you fail to see any output. What could be the cause of this problem?（）

  • A、The IP addresses are configured incorrectly.
  • B、Frame Relay LMI messages not displayed in real time.
  • C、The administrator must issue the enable frame-relay lmi debug command.
  • D、The administrator must issue the terminal monitor command.
  • E、Debug messages can only be received once through the console port.
  • F、The administrator must issue the show frame-relay lmi vty 0 4 command

正确答案:D

更多相关问题
相关内容