CCIE系列认证
单选题Given the following configuration， what command can be used to determine the physical path that traffic will be sent out upon？（） Port-profile type Ethernet name vm-data Switchport mode trunk Switchport trunk allowed vlan 200-210 Channel-group aut
题目
module vem X execute vemcmd show trunk
show module 3 internal pinning
module vem X execute vemcmd show port
show module vem mapping
show interface vethX pinning
参考答案和解析
相似问题和答案
第1题：
A. The default administrative distance is used.
B. The command is used to establish a static route.
C. The command is used to configure the router interfaces.
D. The command is used to establish a stub network.
E. The subnet mask for the source address is 255.255.255.0
第2题：
You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?（）
- A、It is used to restart the router.
- B、It is used to bypass the configuration in NVRAM.
- C、It is used to enter ROM Monitor mode.
- D、It is used to view the lost password.
- E、It is used to save the changes to the configuration.
正确答案:B
第3题：
You are a senior network administrator at Ezonexam, and while performing the password recovery procedure on your 2500 series Cisco router, you type in the following command:
o/r 0x2142
What is the purpose of this command?
A．It is used to restart the router.
B．It is used to bypass the configuration in NVRAM.
C．It is used to enter ROM Monitor mode.
D．It is used to view the lost password.
E．It is used to save the changes to the configuration.
解析：Explanation:
Theo/r 0x2142 command changes the value of config-register to 2142 in a Cisco 2500 series router, so that the Router ignores the NVRAM contents and reverts to the initial setup configuration mode when it boots.
第4题：
What does it mean for a variable in the Application Editor to be defined as a parameter?（）
- A、The variable can be used to pass data to and from subflows.
- B、The value for that variable can be supplied via Application Configuration in Application Administration.
- C、The value for that variable is defined by the calling application.
- D、The variable can be used in conditional steps.
- E、The variable can be used to pass data to and from VoiceXML applications.
正确答案:B
第5题：
Which of the following products and utilities can be used to update all encrypted data as well as the merchant key in a WebSphere Commerce database for a given instance？（）
- A、The Database Update Tool found in Configuration Manager
- B、The LDAP Server
- C、The WebSphere Application Server Administrative Console
- D、The WebSphere Commerce SecurityUpdate Command
- E、The WebSphere Commerce Administration Console
正确答案:A
第6题：
The following configuration command was issued on router TK1:ip route 172.16.3.0 255.255.255.0 192.168.2.1.Which of the following statements are true regarding this command?（）
- A、The command is used to establish a static route.
- B、The default administrative distance is used.
- C、The command is used to configure the default route.
- D、The subnet mask for the source address is 255.255.255.0
- E、The command is used to establish a stub network
正确答案:A,B
第7题：
What is the use of an "all configuration" backup in Cisco UCS？（）
- A、 Can be used to migrate from a 6120 to a 6140 and retain the same service profiles
- B、 Can only be used on the fabric interconnect on which it was created
- C、 Can be used to migrate from a 6120 to 6140 and retain system IP addresses and cluster information
- D、 Can be used to match firmware versions between 6120 and 6140 during a migration
正确答案:A
第8题：
A.TRACERT
B.IPCONFIG/ALL
C.NSLOOKUP
D.PING-T
第9题：
What can be used to stop or start the WebSphere Commerce server？（）
- A、Command Line
- B、WebSphere Commerce Configuration Manager
- C、WebSphere Commerce Administration Console
- D、WebSphere Commerce Accelerator
正确答案:A
第10题：
In the Cisco IOS, what is the definition of a global command?（）
- A、A command that can be entered in any configuration mode.
- B、A command that supports all protocols.
- C、A command that is implemented in all IOS versions.
- D、A command that is set once and affects the entire router.
- E、A command that is available in every release of IOS.
正确答案:D