JN0-102

单选题You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）A The bypass-routing parameter is used to test the density on the T1 line.B The bypass-routing parameter cannot be used on a T1 interface

题目
单选题
You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）
A

The bypass-routing parameter is used to test the density on the T1 line.

B

The bypass-routing parameter cannot be used on a T1 interface.

C

The bypass-routing parameter allows you to ping a host through an interface that has no route through it.

D

The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.

参考答案和解析
正确答案： A
解析： 暂无解析
如果没有搜索结果，请直接 联系老师 获取答案。
相似问题和答案

第1题：

Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.

B. You are attempting to run in the broadcast mode over an NBMA interface.

C. Both routers are configured to function as a BDR; therefore, there is no DR router.

D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.

E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.


参考答案：E

第2题：

You are troubleshooting a frame relay connection and wish to view the LMI traffic stats. Which command should you issue?()

A. Show interface lmi

B. Show frame-relay lmi

C. Show interface frame-relay

D. Debug frame-relay interface.


参考答案：B

第3题：

In the exhibit, what does the (>) symbol indicate?()

A. There is a software issue with ge-1/0/1.0 interface.

B. There is a hardware issue with ge-1/0/1.0 interface.

C. The next hop of 172.25.213.11 is selected.

D. The next hop of 172.25.213.11 is not resolvable.


参考答案：C

第4题：

You issue the ping interface t1-1/1/0 bypass-routing count 1000 rapid command. Which statement is correct?（）

  • A、The count parameter creates a counter that you can view with the show firewall command.
  • B、The count parameter allows the router to count the number of pings for logging purposes.
  • C、The count parameter allows the router to pause for 1000 seconds before sending out a ping.
  • D、The count parameter allows the router to send out 1000 pings and then stop.

正确答案:D

第5题：

While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

  • A、Serial 0 is up, line protocol is up
  • B、Serial 0 is up, line protocol is down
  • C、Serial 0 is down, line protocol is down
  • D、Serial 0 is down, line protocol is up
  • E、Serial 0 is administratively down, line protocol is down
  • F、Serial 0 is administratively down, line protocol is up

正确答案:E

第6题：

While logged into a router you manually shut down the serial 0 interface using the "shutdown" interface configuration command. You then issue the "show interface serial 0" command in exec mode. What could you expect the status of the serial 0 interface to be?（）

A. Serial 0 is up, line protocol is up

B. Serial 0 is up, line protocol is down

C. Serial 0 is down, line protocol is down

D. Serial 0 is down, line protocol is up

E. Serial 0 is administratively down, line protocol is down

F. Serial 0 is administratively down, line protocol is up


参考答案：E

第7题：

Host 1 sends an ICMP echo request to remote sever1. Layer2 header of the frame containing the ping packet（）。

  • A、The IP address of sever 1.
  • B、The MAC address of NIC in sever 1.
  • C、The IP address of F0/0 interface of router R1.
  • D、The MAC address of the Fa0/0 interface of router R1.
  • E、The IP address of the s0/0/0 interface of router R2
  • F、The MAC address of the s0/0/0 interface of router R2

正确答案:D

第8题：

When troubleshooting ATM, which command would allow you to test reachability from one side of an ATM cloud to the other?()

A.ping atm vci 0.100 interface at-0/1/0 end-to-end

B.ping atm vci 0.100 interface at-0/1/0 circuit

C.ping atm vci 0.100 interface at-0/1/0 far-end

D.ping atm vci 0.100 interface at-0/1/0 final-hop


参考答案：A

第9题：

You issue the ping interface tl-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

  • A、The count parameter creates a counter that you can view with the show firewall command
  • B、The count parameter allows the router to count the number of pings for logging purposes
  • C、The count parameter allows the router to pause for 10000 seconds before sending out a ping
  • D、The count parameter allows the router to send out 1000 pings and then stop

正确答案:D

第10题：

You issue the ping interface t1-1/1/0 1.1.1.1 bypass-routing count 1000 rapid command.Which statement is correct?（）

  • A、The bypass-routing parameter is used to test the density on the T1 line.
  • B、The bypass-routing parameter cannot be used on a T1 interface.
  • C、The bypass-routing parameter allows you to ping a host through an interface that has no route through it.
  • D、The bypass-routing parameter allows you to ping a local WAN interface without generating any outbound traffic.

正确答案:C

更多相关问题
相关内容