CMS专题
多选题You are moddifying the default route preference under the [edit protocols] hierarchy. In which two routing information sources can you change the default preference value?（）AlocalBOSPFCdirectDBGP
题目
local
OSPF
direct
BGP
相似问题和答案
第1题：
A.0
B.5
C.10
D.170
第2题：
A. The preference will be 6.
B. The preference will be 7.
C. The preference will be 8.
D. The preference will be the default for static routes.
第3题：
As a Ezonexam trainee you are required to set the default gateway on a Cisco switch to the IP address of 192.168.1.115. Which IOS command should you use?
A．TestKSwitch(config)# ip route-default 192.168.1.115
B．TestKSwitch(config)# ip default-gateway 192.168.1.115
C．TestKSwitch(config)# ip route 192.168.1.115 0.0.0.0
D．TestKSwitch(config)# ip default-network 192.168.1.115
E．None of the above
解析：Explanation:
Use the "ip default-gateway" command to enter the IP address of the next-hop router interface that is directly connected to the switch where a default gateway is being configured. The default gateway receives IP packets with unresolved destination IP addresses from the switch.
Once the default gateway is configured, the switch has connectivity to the remote networks with which a host needs to communicate.
第4题：
A.local
B.OSPF
C.direct
D.BGP
第5题：
A.By default, RIP automatically sends static routes.
B.Configure the static route with a next hop of the RIP neighbor.
C.Configure redistribute static under [edit protocols rip].
D.Apply an export policy within RIP that matches on the routes, and accepts it.
第6题：
A. local
B. OSPF
C. direct
D. BGP
第7题：
A. Lower preference values are more preferred than higher preference values.
B. You can modify the default preference values for any of the routing information sources.
C. By default, a static route is more preferred than a RIP route.
D. A static route is always preferred over a direct route.
第8题：
You need to configure a default route on a Ezonexam router. Which command will configure a default route on a router?
A．VE1(config)# ip route 0.0.0.0 10.1.1.0 10.1.1.1
B．VE1(config)# ip default-route 10.1.1.0
C．VE1(config)# ip default-gateway 10.1.1.0
D．VE1(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
解析：Explanation:Thecommand"IProute0.0.0.00.0.0.0<ip-addressoftheinterface>"commandisusedtoconfigureadefaultrouteonarouter.Inthiscase,adefaultroutewithanexthopIPaddressof10.1.1.1wasconfigured.IncorrectAnswers:A.Thiswillbeaninvalidroute,sincethe"10.1.1.0"valuewillspecifythenetworkmask,whichinthiscaseisinvalid.B,C.Thesecommandsareinvalid.Thecommand"ipdefault-network"couldbeused,butnot"ipdefault-route"or"ipdefault-gateway".IPdefault-gatewayisusedonswitches,notrouters.
第9题：
A.The route is a direct route.
B.The route was selected as active.
C.The route is a default route.
D.The route was learned using a dynamic routing protocol.
第10题：
Refer to the exhibit. A client has asked you to consult on an eBGP loading question. Currently the AS 100 eBGP links have an average outbound load of 65% and 20% respectively. On further investigation, traffic from 10.10.24.0 accounts for 45%, and 10.10.25.0 and 10.10.32.0 accounts for 20% each of the outbound load. The customer wants to spread the load between the two eBGP links more evenly. The BGP attributes are currently set at their default values. If you are located at AS 100 and want to influence how AS 100 sends traffic to AS 200, what BGP attribute could you configure to cause AS 100 outbound traffic to load the eB GP links more evenly? （）
A. On router A, set the default local - preference to 50.
B. On router B, set the default metric to 150.
C. On router B, configure a route map for 10.10.25.0/24 with a local preference of 150 linked to neighbor 192.168.30.2.
D. On router B, set the default local -preference to 150.