CMS专题
单选题Which of the following parameters must be specified to define the number of dispatchers that need to be started？（）A MAX_DISPATCHERSB DISPATCHERSC MIN_DISPATCHERSD SHARED_SERVERS
题目
MAX_DISPATCHERS
DISPATCHERS
MIN_DISPATCHERS
SHARED_SERVERS
相似问题和答案
第1题：
A.The logical volume is created first.
B.The physical volume will be automatically created.
C.The physical partition must be specified as an option.
D.The file system will be mounted during the time of creation.
第2题：
Which of the following is TRUE when creating a file system that resides on the center of a disk?（）
- A、The logical volume is created first.
- B、The physical volume will be automatically created.
- C、The physical partition must be specified as an option.
- D、The file system will be mounted during the time of creation.
正确答案:A
第3题：
第4题：
Prior to 802.1w，Cisco implemented a number of proprietary enhancements to 802.1D to improve convergence in a Layer 2 network. Which statement is correct？（）
- A、Only UplinkFast and BackboneFast are specified in 802.1w；PortFast must be manually configured.
- B、Only PortFast is specified in 802.1w；UplinkFast and BackboneFast must be manually configured.
- C、None of the proprietary Cisco enhancements are specified in 802.1w.
- D、PortFast，UplinkFast，and BackboneFast are specified in 802.1w.
正确答案:D
第5题：
When a new trunk link is configured on an IOS based switch, which VLANs are allowed over the link（）。
- A、By default, all defined VLANs are allowed on the trunk.
- B、Each single VLAN, or VLAN range, must be specified with the switchport mode command.
- C、Each single VLAN, or VLAN range, must be specified with the vtp domain command.
- D、Each single VLAN, or VLAN range, must be specified with the vlan database command.
正确答案:A
第6题：
Which of the following are characteristics of named access lists?（）
- A、Individual statements in a named access list may be deleted.
- B、They require a numbered range from 1000 to 1099.
- C、When created, they must be specified as standard or extended.
- D、They are created with the ip access-list command.
- E、The entire access list must be deleted before editing.
- F、They are applied with the ip name-group command.
正确答案:A,C,D
第7题：
Which one of the following parameters will influence the GSL device utilization the most:（）
- A、PILTIMER
- B、ALPHA
- C、CSPSPRIO
正确答案:A
第8题：
A.A sequence will never generate duplicate values
B.The MAXVALUE of a sequence can be equal to the MINVALUE
C.It is not possible to create a sequence that generates a constant since the INCREMENT value must be greater than zero
D.When a sequence cycles back to either the MAXVALUE or MINVALUE, it will always be equal to the specified value of either of these two boundaries
第9题：
Which two statements are correct about Nonstop Forwarding？（）
- A、It allows the standby RP to take control of the device after a hardware or software fault on the active RP.
- B、It is a Layer 3 function that works with SSO to minimize the amount of time a network is unavailable tousers following a switchover.
- C、It is supported by the implementation of EIGRP， OSPF， RIPv2， and BGP protocols.
- D、It synchronizes startup configuration， startup variables， and running configuration.
- E、The main objective of NSF is to continue forwarding IP packets following a switchover.
- F、Layer 2 802.1w or 802.1s must be used， as 802.1d cannot process the Layer 2 changes.
- G、Routing protocol tuning parameters must be the same as the NSF parameters， or failover will beinconsistent.
正确答案:B,E
第10题：
When using CHKDSK, which of the following parameters locks the volume, locates bad sectorsand recovers readable information?（）
- A、/r
- B、/f
- C、/i
- D、/x
正确答案:A