单选题Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt show

A. R2 will forward all packets that enter Fa0/0 per the PBR configuration.

B. R2 will use route map RM2 when determining how to forward packets that exit interface Fa0/1.

C. R2 will consider using PBR for all packets exiting S0/0 /0 per route map RM3.

D. R2 will consider using PBR for all packets entering S0/0/0 per route map RM3.

Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0

B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0

C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0

D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0

E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0

F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2‘s F0/0 interface. Which of the following is true about R1‘s route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64

A. The next hop is 2000::1311:11FF:FE11:1111

B. The next hop is FE80::1311:11FF:FE11:1111

C. The next hop is FE80::5111:11FF:FE11:1111

D. The next hop is 2001::1

Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）

A. both routers R1 and R2

B. router R1

C. router R2

D. none of the routers since they are not configured with static RP

Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A. Add the area 1 stub command on routers R1.

B. Add the always keyword to the default - information originate configuration command on router R2.

C. Remov e the default information originate configuration command from router R2 and place it on router R1.

D. Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

Routers R1 and R2 are OSPF neighbors using their Fa0/0 interfaces, respectively, using default settings for all timers. An engineer ad ds the ip ospf hello - interval 6 command to R1‘s Fa0/0 configuration.Which of the following is true regarding the results from this change?（）

A. The show ip ospf neighbor command on R1 lists the revised Hello timer

B. The show ip ospf interfac e brief command on R1 lists the revised Hello timer

C. The R1 - R2 neighborship fails due to Hello timer mismatcH

D. The show ip ospf interface command on R1 lists the revised Hello timer

Refer to the exhibit. EIGRP had converged in AS 1 when the link between router R1 and R2 went down. The console on router R2 generated the following messages:*Mar 20 12:12:06: %DUAL - 5NBRCHANG E: IP - EIGRP 1: Neighbor 10.1.4.3 (Serial0) is down: stuck in active*Mar 20 12:15:23: %DUAL -3- SIA: Route 10.1.1.0/24 stuck - in - active state in IP - EIGRP 1.Cleaning up The network administrator issued the show ip eigrp topology active command on R2 to check the status of the EIGRP network.Which statement best describes the reason for the error messages?（）

A. Incorrect bandwidth configuration on router R3 prevents R2 from establishing neighbor adjacency.

B. Incorrect bandwidth configuration on router R 5 prevents R2 from establishing neighbor adjacency.

C. Router R3 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

D. Router R5 did not reply to the query about network 10.1.1.0/24 sent by router R2 .

Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）

A. 22

B. 11

C. 1

D. None

Refer to the exhibit and the partial configuration on router R2. On router R4 all RIP routes are redistributed into the OSPF domain. A second redistribu tion is configured on router R2 using a route map. Based on the configuration on router R2, which EIGRP external routes will be present in the routing table of R1?（）

A. the routes originating from the RIP routing domain

B. the routes originating from the OSPF stub area

C. all OSPF inter and intra - area routes

D. all routes originating from RIP and OSPF routing domains

Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1‘s Fa0/0 configuration.Which of the following is true regarding the results from this c hange？（）

A.The show ip eigrp neighbors command on R1 lists the revised Hello timer

B.The show ip eigrp interfaces command on R1 lists the revised Hello timer

C.The R1 - R2 neighborship fails due to Hello timer mismatcH

D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer